Seiko TM-L60 Návod k obsluze

thermal line printerTM-L60Operator’s Manual400179501

1-4Names and Functions of Partsn Part namesÀ Roll-paper coverÁ Operation panel Power connectorà Interface connectorÄ Drawer kick-out connectorÅ DIP s

n Operation panelPanel switches POWERPress the POWER button to turn the printer ON and OFF. When the button ispushed down, the power is on. When press

Chapter 2 Before Setting Up2-1Connecting the Power Supply to the Printern Plugging in AC adapterThe printer must be connected to an external power sup

2-2Connecting the Host Computer to the Printern Connecting the interface cableConnect the printer to a host ECR (host computer) using an interface cab

Chapter 3 Installing the Parts3-1Installing the Roll Papern Installing the roll paperBe sure to use roll paper that matches the printer’s specificatio

Insert the edge of the roll paper into the paper slot and feed the paper 5 cmbeyond the tear-off edge.Tear-off -EdgePaper SlotUnroll the paper a li

3-2 Adjusting the Paper-end Detectorn The paper-end detectorThe paper-end detector senses when the paper is nearing its end and turns on thePAPER lamp

Loosen the adjusting screw that holds the paper-end detector. Then set the topof the positioning plate to the appropriate adjustment position, a

3-3 Setting the DIP Switchesn Locating the DIP switchesOn the underside of your printer are a number of DIP switches that can be set toperform a numbe

n n DIP-Switch FunctionsTable 3-2. DIP-switch FunctionsDIP SW ONOFFSW-1SW-2Ignores data reception errorsPrints “?” for data reception errorsData buff

All rights reserved., No part of this publication may be reproduced, stored in a retrievasystem, or transmitted in any form or by any means, mechanica

Chapter 4 The Self Test4-1Checking Operation with the Self Testn The purpose of the self testThe self test checks whether the printer has any problems

II. REFERENCE

Chapter 5 Cautions while Usingthe Printer5-1Panel Switches and Commandsn Switches(1) Power switch[Function] Turns the power supply on/off.[Note]l The

5-2Printable Area and Label Paper Conditionsn Printable areaThe print area must be within the range indicated below.Roll paper[Units: mm]Label paper(A

5-3 Miscellaneous Notesn Notes on printing and paper feeding(1)Because the TM-L60 is a line printer, it automatically feeds paper after printingthe da

(2)When the printer goes to the standby (data-waiting) state during printing, theprinter stops printing and feeding paper temporarily. When the printe

d) If thermal paper touches anything which includes phthalic acid esterplasticizer for a long period, it can reduce the image formation ability of th

Table 5-3. Error DisplayErrorRAM check errorON/OFF Timing PatternRecovery150 msImpossible to recover.ONOFF150 msTransistor error150 ms1800 msImpossibl

ErrorON/OFF Timing PatternRecoveryPrint head overheating150 msRecovers automati-errorONcally when the printhead temperaturedrops back down.OFF150 ms 1

5-5 Cleaning the Headn n Cleaning the headClean the head according to the following procedure.CAUTION:l Do not clean the head immediately after printi

CC CLASS AFCC COMPLIANCE STATEMENT FOR AMERICAN USERSThis equipment has been tested and found to comply with the limits for aClass A digitaldevice, pu

5-6 The Cover-open Detectorn n The cover-open detectorThis unit has an cover-open detector located inside the roll-paper cover.l Data is not printed w

Chapter 6 Software Control6-1 Printer Controln Controlling the printer with commandsThe printer is controlled by “commands” that can change the size o

6-2 Command Descriptionsn Command descriptionsXXX Command[Name][Format][Range][Description][Notes][Default][Reference][Example]The name of the command

LF[Name]Print and line feed[Format]<OA> H[Description] Prints the data in the print buffer and performs 1 line feed basedon the current line spa

ValueBitFunction010Character fontFont AFont B1Undefined2Undefined3EmphasizedCanceledSet4Double-heightCanceledSet5Double-widthCanceledSet6 Undefined7Un

ESC % n[Name]Select/cancels user-defined character set.[Format]<1B> H <25> H <n>[Range]0 n 255 [Description]Select

[Default]The same as the internal character set.[Reference]ESC %[Example]l Font A is selected:l Font B is selected.ESC * m n1 n2 [d] k[Name][Format][R

[Description]Sets the bit-image mode using m and the number of dots usingn1 and n2.l Divide the number of dots to be printed by 256.The integer an-swe

l 24-dot bit imageESC 2[Name]Set 1/6 inch line spacing[Format]<1B>H<32>H[Description]Sets the line spacing to 1/6 of an inch.ESC 3 n[Name]

l Each bit of n is used as follows:ValueBitDevice010PrinterInvalidValid1Undefined2 Undefined3Undefined4Undefined5Undefined6Undefined7Undefined[Notes][

INTRODUCTIONThe TM-L60 is a available as a simplificative bar code printer for the followinguses:l One-station printer for ECR and POS usel Output dev

l A horizontal tab position is stored as the absolute value of(character width X n ) measured from the beginning of the line.The character width inclu

[Example]Normal characterEmphasized characterESC G n[Name]Select/cancel double-strike mode[Format]<1B>H<47>H<n>[Range]0 n

ESC R n[Name]Select international character set[Format]<1B>H<52>H<n>[Range]0 n 10[Description]n selects an internationa

ESC ¥ n1 n2[Name][Format][Range][Description][Notes][Default][Reference]ESC - nSet relative position<1B>H<5C>H<nl><n2>0 n

l n specifies the alignment as follows:nPosition0Align left1Align center2Align right[Notes][Default][Example]l Valid only when input at the beginning

l In the TM-L60, only the journal near-end detector can be se-lected and only the lowest bit of n is valid.[Notes][Default]l When a paper-end is detec

[Description]The pulse defined by nl and n2 is output on connector pin m.l m is specified as follows:mConnector pin 0 Drawer kick-out connector

[Notes]l The transmitted status is only one byte and the data is as shownin the following table.l If nothing is connected with Drawer kick-out connect

ValueBitFunction 010Journal near-endPaper is present Paper is out1Undefined2UnusedFixed to 03Undefined4UnusedFixed to 05Undefined6Undefined7UndefinedE

GS FF[Name]Print and eject label[Format]<1D>H<OC>H[Description]Prints the data in the print buffer on the label and ejects it.l Ejects the

About this manual* Chapter 1 contains information on unpacking the printer, choosing the place forthe printer, and names and functions of parts.* Chap

GS/m[Name]Print down-loaded bit image[Format] <1D>H<2F>H<m>[Range][Description]Prints a down-loaded bit image using the mode specifi

GS :[Name]Set starting/ending of macro definition[Format]<1D>H<3A>H[Description]Specifies the starting or ending of the macro definition.I

l “mu indicates adjusting direction.When m = < * * * * * 0>B, positioning is adjusted in thenormal direction.When m = <* * * * * * 0>B, po

m = 1 to 5:The maximum number of digits to be printed. Whenthe numerical value of the counter value is largerthan that specified by this command, prin

With count-downl Counts down n1 + n2 x 256 > n3 + n4 x 256, n5 ≠ 0, and n6 ≠0.l n1 + n2 x 256 means the maximum counter value and n3 + n4 x256 the

[Default]n1 + n2 x 256 = 1[Reference]GS CO, GS Cl, GS c, GS C;GSC; N1; N2; N3; N4; N5;[Name]Select count mode (B)[Format]<1D>H<43>H<3B&

l If the counter value set by N5 goes out of the counter operationrange, it will be forced to convert to the minimum by GS c.With counting downl If th

[Notes]l The syntax to be used when setting data in the print buffershould be based upon GS CO.l For count mode, see GS Cl or GS C;.With counting upl

GS k n [d] k NUL[Name]Print bar code[Format]<1D>H<6B>H<n> [<d>]k<00>H[Range]0 ≤ n ≤ 6[Description]Selects a bar code sys

GS ^ n1 n2 n3[Name] Execute macro[Format]<1D>H<5E>H<n1><n2><n3>[Range]0 ≤ n1 ≤ 2550 ≤ n2 ≤ 2550 ≤ n3 ≤ l[Description] Ex

Chapter 4 The Self Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-4 Program Descriptions1. IntroductionThe TM-L60 is connected to the host computer by an RS-232C Interface.The TM-L60 is easily controlled by sendin

 Send Print Data120 PRINT #1, “ABCDEF”; CHR$( 10);Always send a LF code (CHR$ (10)) after print data. To execute printing, senda LF code or ensure th

Æ Selecting the character code table.190FOR I =240TO255200PRINT #l, CHR$(I);210 NEXT I220’230 PRINT #l , CHR$(27); “t”; CHR$( 1);240’250FOR I =240 TO2

The 12 characters, “012345678901” are print data.A check-digital is added by the printer because 12 characters are sent, and“012345678901” is printed.

g g Sample Program onto thermal paper100 OPEN “COMl : N81 NN” AS #1110 PRINT #l , CHR$(27); “@ ";120 PRINT #1, “ABCDEF”; CHR$( 10);130 PRINT #l,

3-2. Printing on label paperÀ Open device RS-232C.100 OPEN “COM 1: N81NN” AS #lÁ Initialize the printer mechanism.110 PRINT #1, CHR$(29); “<“;Â Sen

Å Print and eject label210 PRINT #l, “ABCDEF”; CHR$( 10);220 PRINT #l, CHR$(29); CHR$( 12);210 prints data, then 220 ejects label. After ejection, an

APPENDIXAPPENDIX A General Specifications1. Printing specificationsPrinting method:Dot density:Printing direction:Print width:Characters per line:Ther

Character structure:Character size:Font A:12 x 24 (includes the horizontal 2-dot space)Font B:9 x 17 (includes the horizontal 2-dot space)Default:Font

Paper width:Roll size:Specified paper:Roll paper core:4.2 Thermal label paperPaper type:Paper thickness:Form:Paper width:Roll size:Specified paper:Rol

1. SETTING UP

6. Electrical characteristicsSupply voltage:24 VDC ± 7% (Optional power supply:PS-130)Current consumption:Operating:Mean: Approx. 1.3 A(Print duty: 30

APPENDIX B Connectors1. ConnectorsSerial Interface ConnectorPower Supply ConnectorDrawer Kick-out Connector2. Interface connectorsSee APPENDIX C Inter

Pin Number Signal NameSender3SW (+)Cash drawer45L (+)L2 (-)PrinterPrinter6SW (-)-----I I2) Drawer kick-out drive signalConnected to:Cash drawerCash d

n1 x 2 msn2 x 2 msFigure B-1. Drawer Kick-out Drive SignalPrinter sideUser sideFigure B-2. Drawer Kick-out Signal Interface CircuitNOTES: l The circui

2. Interface connector terminal assignments and signal functions Pin Number Signal Name Signal Direction FunctionI1FG-Frame ground2TXDoutputTransmit

International character set71

APPENDIX E Command SummaryCommandNameReference PageHTHorizontal tab26LFPrint and line feed27FFPrint and position label to start printing27ESC SPSet ch

CommandNameReference PageESC tISelect character code table40ESC uESC vESC {Transmit peripheral device status40Transmit printer status41Set/cancel upsi

Chapter 1 Unpacking the Printer1-1 Checking the Contents of the Boxg Checking the partsRemove the printer and other parts from the box.• Roll paper• P

1-2Choosing a Place for the Printern Avoid locations that are subject to direct sunlight or excessive heat (nearheaters).n Avoid using or storing the